Tuesday, November 30, 2010

How to Test Brake Boosters

Power brakes represent one of the greatest advances in automotive braking technology. Not only do power brakes make it easier for the driver to stop the vehicle, but without the assistance of the power booster it would be practically impossible for disc brakes to be effectively used on automobiles. Any deficiencies in the performance of a power booster can seriously impair braking effectiveness, and it is important to be sure the booster is operating properly at all times. Testing the booster is a simple job that every driver can do.

Procedures:
1. Turn the vehicle engine off and pump the brake pedal a few times to deplete any remaining vacuum in the power booster. Push and hold the brake pedal down with light but steady pressure. Start the engine. The brake pedal should drop slightly, indicating that the booster is working properly.
2. Allow the engine to run at idle for a minute or two. Turn the engine off and slowly pump the brake pedal five or six times. The brake pedal should stop at a higher position with each pump, indicating that the booster is not leaking and the check valve is working properly.
3. Start the engine and allow it to run at idle for a minute or two. Push and hold the brake pedal down with light but steady pressure, and turn the engine off. Continue holding the pedal down for 30 seconds or so. If the pedal does not rise it indicates that the booster is not leaking and the check valve is working properly.
4. Test the vacuum booster check valve. Locate the vacuum booster. It is a dome shaped assembly mounted at the rear of the engine compartment on the driver's side. Now locate the flexible vacuum hose that runs from the engine intake manifold to the vacuum booster. Remove any retaining clips that hold the hose to the intake manifold connection, and slip the hose off the connection. Try to blow into the hose. If the check valve is working properly the air will not flow into the booster. Now try to suck air out of the hose. If the check valve is working properly air will flow out of the booster.
5. Connect an engine vacuum test gauge to the connection on the engine intake manifold. Start the engine and let it run for a minute or two. Check the test gauge vacuum reading. The vacuum should be at least 18 inches.
Read More »»

Sunday, November 28, 2010

Test an 88 GMC Brake Booster

The brake power booster uses vacuum generated in the engine intake manifold to amplify the force the driver exerts on the brake pedal, making the driver's job easier when slowing or stopping the vehicle. This is especially important on large vehicles like those made by GMC. Problems with the power booster can create a dangerous situation because the driver may unexpectedly need much greater effort when braking. If the braking seems to be more difficult than normal it is time to test your brake booster. Testing the booster is an easy task that every driver can do to assure herself that it is functioning properly

Procedures:
1. Park your 88 GMC and turn the engine off. Pump the brake pedal slowly five or six times to relieve any residual vacuum in the booster. Push the brake pedal down and hold it down with light but steady force. The brake pedal should feel harder and higher than normal. Start the engine. The brake pedal should immediately drop 1/4-inch or so and it should suddenly feel normal. If your booster is not functioning properly the pedal will stay in a high position and will feel hard.
2. Let the engine idle for a couple of minutes. Turn the engine off and slowly pump the brake pedal, waiting a couple of seconds between each pump. The pedal should go down to a normal position on the first pump, and then stop a little bit higher with each following pump.
3. Start the engine again and let it idle for a couple of minutes. Push the brake pedal down and hold it down with light but steady force. Turn the engine off and continue to hold the brake pedal down for about a minute or so. The pedal should not rise during this time.
Read More »»

Remove Extremely Tight Bolts

Bolts that have been in place for a long time often become so rusted they cannot easily be loosened with a wrench or socket. Exposure to moisture makes them even rustier. Trying to force a bolt will likely just damage the head of the bolt, making it even harder to remove. Trying to force off a rusted bolt can also injure a worker's hands, especially if the socket or wrench slips. There are, however, effective and safe ways of loosening tight and rusted bolts.

Procedures:
1. Spray a commercial rust-removing solution or lubricant on and around the bolt, trying to cover as much of the bolt as possible. Wait a few minutes. Loosen the bolt, if possible, with a wrench.
2. Use a propane torch to heat the top of the bolt if it remains stuck. Before applay a flame, though, wipe up or dry off with a rag any remaining rust-removing solution or penetrating oil around the bolt. Flames and petroleum-based solvents aren't a good combination. Heating the top will cause the entire bolt to expand. It should take about a minute.
3. Place a wrench back on top of the bolt and turn counterclockwise. If the bolt becomes too rounded for the wrench to fit properly, tighten a pair of lock pliers onto the head of the bolt. Once it is locked into place, push or pull the pliers counterclockwise to loosen the bolt, using as much force as necessary. If the bolt still will not turn, tap the pliers with a hammer counterclockwise until it loosens.
4. Put a socket onto the head of the bolt if it still will not loosen and then place a short piece of pipe over the socket handle. This piece of pipe is often called either a buster bar or a cheater bar. Grab hold of the buster bar and push or pull counterclockwise until the bolt loosens. Do not use too much force or the socket might break.
5. Cut off the top of the bolt with a hacksaw if it still will not loosen. A cold chisel or reciprocating saw may be used instead. Another way to break the bolt is to use a nut splitter. It will break the nut without damaging the threads of the bolt.
6. Remove the rest of the bolt with a screw extractor. Take the drill bit that came with the screw extractor and place it in a drill. Then drill a hole through the center of the bolt. Place the screw extractor in the recently drilled hole and turn counterclockwise until the bolt is removed.
Read More »»

Replace 330I Rear Pads

The BMW 330I is a luxury car, but the parts wear just like any other automobile. The brake pads and rotors stop the car with friction. Friction wears out the brake pads and you need to replace them. Replacing the pads, however, only takes about 30 minutes per wheel. When you are replacing the brake pads, you should inspect the brake rotors. If you put new pads on rotors that have grooves or other damage, it will not be long before you have to replace the pads again.

Procedures:
1. Park the BMW on a level surface and turn the key off. Open the engine compartment and locate the master brake cylinder. You will find it on the back firewall of the engine compartment, on the driver's side of the car. Siphon about half of the brake fluid from the master cylinder with the turkey baster. Place the fluid in the drain pan. You will need to recycle it later. It is not a good idea to reuse brake fluid in the master cylinder.
2. Place the wheel chocks in front of the front tires. Raise the back end of the BMW with the automobile jack on the side you will be working on. Place a jack stand under the car near the jacking point and raise it to the frame. Remove the lug nuts with the lug wrench and pull the wheel from the car.
3. Remove the top bolt on the brake caliper with a socket and ratchet. Pivot the brake caliper off the rotor and remove the brake pads. Insert the piston tool in the caliper and twist the handle to seat the piston back into the caliper housing. Clean the caliper thoroughly with the wire brush.
4. Insert the new brake pads into the caliper and push it onto the rotor. Tighten the bolt with the socket and ratchet. Place the wheel on the car and tighten the lug nuts. Remove the jack stand from under the BMW. Lower the vehicle to the ground. Repeat the process on the other wheel.
5. Check the brake fluid level in the master cylinder and add to it as necessary. Pump the brake pedal until it feel firm.
Read More »»

Install a Summit Differential Cover

Differential covers keep the gears and oil inside a vehicle's rear end. Older vehicles use a differential cover with no drain or vent plugs. This makes it necessary to remove the differential cover each time you perform a rear end oil change. Summit Racing differential covers are made from lightweight aluminum and have the plugs required to change oil without removing the cover. This saves time and money when you need to change the oil in your rear differential.

Procedures:
1. Apply the vehicle's parking brake. Set a wheel chock under each of the vehicle's rear wheels.
2. Set a drain pan under the differential housing. Remove the bolts from the differential housing cover with a socket matching the bolt heads attached to a 3/8-inch ratchet handle. Allow the oil to drain from the housing for five to 10 minutes.
3. Scrape the old gasket from the cover mounting flange of the differential house with a metal putty knife. Spray aerosol brake cleaner on the flange. Wipe the flange with a clean rag to remove remaining debris and oil.
4. Apply RTV sealant to the flanges of the Summit differential cover and the differential mounting flange. Press a differential gasket into the sealant, which is on the differential cover flange. Push the cover onto the differential flange.
5. Thread the differential cover bolts through the Summit differential cover and into the differential housing. Tighten the bolts with the socket and 3/8-inch ratchet handle.
6. Remove the top fill plug from the Summit differential cover with a 3/8-inch ratchet handle.
7. Cut the ends off the nozzle of a differential oil tube. Pour the oil into the differential. Repeat the process until the oil level reaches the bottom of the fill hole. Install the fill plug into the Summit differential cover.
Read More »»

Saturday, November 27, 2010

Replace the Disc Pads on a Honda Odyssey

The brake pads on the Honda Odyssey work with the rotors and stop your car using friction. The friction wears out the brake pads, which should be replaced periodically. It not a hard project to complete, and you can finish each wheel in about 30 minutes. When you change your brake pads, inspect the rotors. The same friction wears the rotors down, though not as quickly as it does with the brake pads. If you find any grooves on the surface of the rotors, you should deal with those as well

Procedures:
1. Park the Honda on a level surface and turn off the ignition. Place wheel chocks behind the rear wheels. Open the engine compartment and siphon 2/3 of the brake fluid from the master cylinder with the turkey baster. Put the fluid in the drain pan to recycle later. Raise the Odyssey up with the automobile jack. Place a jack stand under the van near the jacking point and raise it to the frame. Remove the lug nuts with the lug wrench and take the wheel off the van.
2. Remove the brake hose bolt from the bracket using a socket and ratchet. Loosen the lower caliper bolt with the socket and ratchet. Pivot the caliper up and remove the brake pads. Clean the caliper surface with the wire brush. Push the piston into the caliper housing with a brake piston tool.
3. Install the new brake pads and push the caliper down onto the rotor. Tighten the bolt with the socket and ratchet. Install the brake hose bolt into the bracket and tighten it with the socket and ratchet. Put the wheel back on the Odyssey and tighten the lug nuts with the lug wrench. Remove the jack stand from under the van and lower the vehicle to the ground. Repeat the process on the other wheel.
4. Check the brake fluid and add to the master cylinder as needed. Pump the brake pedal until it is firm to seat the brake pads on the rotors.
Read More »»

Change Brake Pads Step-by-Step

The brake pads are attached to a caliper that apply pressure to the rotor to stop the vehicle. The pads wear out over time and this can cause the metal backing on the pad to scrub the rotor. The pads will not take very much time to replace once the wheels are removed.

Procedures:
1. Ensure the vehicle is parked on a flat and level surface. Set the parking brake to ensure the vehicle does not roll back.
2. Loosen the lugnuts on both front wheels with a tire tool but do not remove them. This will make removing the wheels easier when the vehicle is raised up.
3. Place a jack underneath the front crossmember of the vehicle. Raise the car high enough to place jack stands under the crossmember. Lower the vehicle on to the crossmembers.
4. Remove the lug nuts on the driver side with a tire tool. Take the wheel off the axle and place it to the side.
5. Locate the two bolts at the back of the caliper. The caliper is mounted directly over the rotor. Unscrew the two bolts with a socket wrench. Pull the caliper off by sliding it up and off the rotor.
6. Unclip the brake pads from the caliper. They will come out with a little force. Install one of the brake pads backwards in to the back of the caliper. Place a C-clamp over the old pad and the back of the caliper. Turn the handle on top of the clamp to tighten. The force will push the brake pad in to the piston. The piston will fully retract back in to the caliper. This will make installation easier on the new pads.
7. Place the new pads on to the caliper. They will clip in place once they are pushed in to place.
8. Position the caliper over the rotor. Start both bolts by hand before tightening them. Once both bolts are installed, tighten with a socket wrench.
9. Repeat to replace brake pads on the other wheel. Tighten the wheels on to the hub with a tire tool. Tighten the lug nuts in a criss-cross pattern.
10. Raise the vehicle to remove the jack stands. Lower the vehicle to the ground.
11. Start the vehicle and allow it to idle. Pump the brake pedal to reset the calipers.
Read More »»