The brakes on the 2000 Ford Windstar should be inspected regularly. Owners should look for wear and damage to the brake pads and rotors, as well as ensure there is adequate brake fluid in the vehicle, for the brakes to function properly. Ford recommends replacing the brake pads every 50,000 miles. You can choose to have the pads replaced at a brake repair shop, or you can do it yourself to save time and money
Procedure:
1. Loosen the lug nuts on the front wheels with a lug wrench. Place the jack under the frame at the front of the van, and lift the front tires off the ground. Place jack stands under the axles, and lower the Ford onto the stands.
2. Remove the lug nuts, and take off the front wheels. Remove the two caliper slide bolts on the back side of the right brake caliper, with a 10-mm wrench. Lift the caliper from the brake assembly, and rest it on top of the steering arm, above the brakes.
3. Pry the two brake pads from the caliper bracket with a flat screwdriver. Inspect the caliper bracket slots and rotor for damage or significant wear. Clean the area with a wire brush and brake parts cleaner.
4. Apply a thin layer of brake grease to the back side of the new brake pads. Slide the pads into the caliper bracket slots.
5. Open the brake bleed valve with the 10-mm socket wrench. The valve is located between the two caliper slide bolts. Place a drip pane below the brake, to capture the brake fluid.
6. Compress the caliper piston into the side of the caliper with a C-clamp. The piston is the metal cylinder that protrudes from the inside of the caliper. Open the piston to allow for the added space of the new brake pads. Close the brake bleed valve with the wrench.
7. Replace the caliper onto the new brake pads and caliper bracket. Screw in the caliper bolts, and tighten the pins with the wrench. Replace the wheel onto the wheel bolts, and screw on the lug nuts, by hand. Lift the Windstar with the jack, and remove the jack stands. Lower the tires to the ground, and tighten the lug nuts with the lug wrench.
8. Lift the Ford Windstar hood, and remove the master cylinder cap. Place a funnel inside the brake fluid reservoir, and add new fluid, as necessary. Remove the funnel, and replace the cap. Close the hood.
Read More »»
Wednesday, November 17, 2010
Replace GMC Brake Rotors
GMC is a manufacturer of trucks and sport utility vehicles. The brake rotors ensure the brake pads have a smooth surface to apply pressure, when the brakes are engaged. A warped rotor will cause the vehicle to vibrate when coming to a stop. Replacement of the rotor will not take long, once the truck is raised
Instructions Procedure:
1. Ensure the truck is parked on a level surface. Set the parking brake, and chock the back wheel.
2. Loosen the lug nuts on the front wheels with a tire tool. Do not remove the lug nuts, until the truck is raised off the ground.
3. Place a jack under the cross member of the front of the truck. Raise the truck high enough to place the jack stands under the front crossmember. Lower the truck on to the jack stands.
4. Remove the lug nuts from the wheel. Take the wheel off, and place it to the side.
5. Locate the caliper, resting on the top of the rotor. Loosen the bolts at the back of the caliper with a socket wrench. Pull the caliper off the back of the rotor, by hand, after the bolts are removed.
6. Pull the brake pads out of the holder by hand. Unbolt the brake pad holder with a socket wrench. Pull the holder off the rotor.
7. Pull the rotor off the hub assembly by hand. Tapping the rotor with a hammer will loosen it, if it is stubborn.
8. Slide the new rotor on to the hub assembly. The rotor will rest on the studs.
9. Bolt the brake pad holder over the rotor with a socket wrench. Insert the brake pads onto the holder.
10. Rest the caliper over the brake pad holder. Tighten the bolts with a socket wrench, to secure it in place.
11. Place the wheel back on to the axle. Repeat steps to replace the remaining rotor.
12. Tighten the wheels, by tightening the lug nuts with a tire tool. Tighten them in a crisscross pattern, to ensure the wheel is tightened correctly.
13. Raise the truck, and remove the jack stands. Lower the truck to the ground.
14. Double check all the lug nuts, to ensure they are all tight. Check both wheels.
15. Test drive the truck, to ensure the truck brakes smoothly and without any vibrations. Read More »»
Instructions Procedure:
1. Ensure the truck is parked on a level surface. Set the parking brake, and chock the back wheel.
2. Loosen the lug nuts on the front wheels with a tire tool. Do not remove the lug nuts, until the truck is raised off the ground.
3. Place a jack under the cross member of the front of the truck. Raise the truck high enough to place the jack stands under the front crossmember. Lower the truck on to the jack stands.
4. Remove the lug nuts from the wheel. Take the wheel off, and place it to the side.
5. Locate the caliper, resting on the top of the rotor. Loosen the bolts at the back of the caliper with a socket wrench. Pull the caliper off the back of the rotor, by hand, after the bolts are removed.
6. Pull the brake pads out of the holder by hand. Unbolt the brake pad holder with a socket wrench. Pull the holder off the rotor.
7. Pull the rotor off the hub assembly by hand. Tapping the rotor with a hammer will loosen it, if it is stubborn.
8. Slide the new rotor on to the hub assembly. The rotor will rest on the studs.
9. Bolt the brake pad holder over the rotor with a socket wrench. Insert the brake pads onto the holder.
10. Rest the caliper over the brake pad holder. Tighten the bolts with a socket wrench, to secure it in place.
11. Place the wheel back on to the axle. Repeat steps to replace the remaining rotor.
12. Tighten the wheels, by tightening the lug nuts with a tire tool. Tighten them in a crisscross pattern, to ensure the wheel is tightened correctly.
13. Raise the truck, and remove the jack stands. Lower the truck to the ground.
14. Double check all the lug nuts, to ensure they are all tight. Check both wheels.
15. Test drive the truck, to ensure the truck brakes smoothly and without any vibrations. Read More »»
Replace Rear Pads on a Mazda
Replace the rear brakes on the Mazda is not difficult. Disc brakes work by using friction between the brake pads and rotors. Friction wears down the brake pads, and you will have to replace them periodically. Brake pad wear is relative to the amount of use the brakes get. You want to make sure that you inspect the rotors when you change the brake pads. If the rotors are bad, you will need to replace them, or they will only damage your new brake pads.
Procedures:
1. Park the Mazda on a level, paved surface and turn off the engine. Open the engine compartment and siphon about ½ of the brake fluid from the master cylinder with a turkey baster. Put the fluid in a drain pan for recycling. Place wheel chocks in front of the front wheels. Raise the Mazda with the automobile jack. Place a jack stand under the car and raise it to the frame. Remove the lug nuts from the wheel with a lug wrench and pull the wheel from the car.
2. Loosen the top bolt on the brake caliper with a socket and ratchet. Pivot the caliper in a downward motion and pull it from the brake rotor. Remove the brake pads from the caliper. Insert the piston tool into the caliper and twist the handle until the piston seats itself within the caliper housing.
3. Install the new brake pads into the caliper. Insert the shims behind the brake pads. Pivot the caliper upward and onto the rotor. Tighten the bolt with the socket and ratchet. Remount the wheel onto the car and tighten the lug nuts with the lug wrench. Remove the jack stand from under the car and lower it to the ground. Repeat the process on the other wheel.
4. Add brake fluid, as needed, to the master cylinder. Pump the brake pedal a few times until the brake pads seat themselves on the rotors and the pedal feels firm. Read More »»
Procedures:
1. Park the Mazda on a level, paved surface and turn off the engine. Open the engine compartment and siphon about ½ of the brake fluid from the master cylinder with a turkey baster. Put the fluid in a drain pan for recycling. Place wheel chocks in front of the front wheels. Raise the Mazda with the automobile jack. Place a jack stand under the car and raise it to the frame. Remove the lug nuts from the wheel with a lug wrench and pull the wheel from the car.
2. Loosen the top bolt on the brake caliper with a socket and ratchet. Pivot the caliper in a downward motion and pull it from the brake rotor. Remove the brake pads from the caliper. Insert the piston tool into the caliper and twist the handle until the piston seats itself within the caliper housing.
3. Install the new brake pads into the caliper. Insert the shims behind the brake pads. Pivot the caliper upward and onto the rotor. Tighten the bolt with the socket and ratchet. Remount the wheel onto the car and tighten the lug nuts with the lug wrench. Remove the jack stand from under the car and lower it to the ground. Repeat the process on the other wheel.
4. Add brake fluid, as needed, to the master cylinder. Pump the brake pedal a few times until the brake pads seat themselves on the rotors and the pedal feels firm. Read More »»
Tuesday, November 16, 2010
How to Change the Brake Pads on a Taurus
The Ford Taurus has a four-wheel disc brake system that consists of a brake master cylinder, brake lines, brake calipers, brake rotors and brake pads. When you hit the brakes, you send a mechanical force into the master cylinder, which in turn sends hydraulic fluid down the brake lines to the brake calipers. The hydraulic pressure contracts the caliper, forcing the pads against the rotors and stopping the Taurus. A byproduct of this action is brake pad wear, which eventually leads to the need to replace the brake pads. People with basic auto-repair skills can change a Taurus' brake pads in about two hours.
Shove the wheel chocks against the front and back of the left-rear tire. 1. Loosen all the Taurus' front lug nuts with the lug wrench.
2. Lift the front of the Taurus with the floor jack and support it on jack stands. Remove the car's front lug nuts and wheels manually.
3. Position the drop pan under the left-front brake assembly. Wash the brake dust off the rotor and caliper with brake cleaner.
4. Remove the Taurus' left-front caliper bolts with the socket set. Lift the caliper from the caliper bracket by hand. Pull the old pads out by hand and throw them away.
5. Wash the inside of the caliper with brake cleaner to remove the brake dust, road dirt and old grease. Lubricate the caliper slides with white lithium grease.
6. Position the Taurus' new brake pads in the caliper by hand. Lower the caliper into the left-front caliper bracket. Bolt it into place using the socket set.
7. Move to the Taurus' right-front brake assembly and repeat steps 3 through 6. Reinstall the wheels and lug nuts by hand.
8. Lower the front end off the jack stands. Tighten the front lug nuts to 85 foot-pounds with your torque wrench. Move the wheel chocks before driving the Taurus. Read More »»
Shove the wheel chocks against the front and back of the left-rear tire. 1. Loosen all the Taurus' front lug nuts with the lug wrench.
2. Lift the front of the Taurus with the floor jack and support it on jack stands. Remove the car's front lug nuts and wheels manually.
3. Position the drop pan under the left-front brake assembly. Wash the brake dust off the rotor and caliper with brake cleaner.
4. Remove the Taurus' left-front caliper bolts with the socket set. Lift the caliper from the caliper bracket by hand. Pull the old pads out by hand and throw them away.
5. Wash the inside of the caliper with brake cleaner to remove the brake dust, road dirt and old grease. Lubricate the caliper slides with white lithium grease.
6. Position the Taurus' new brake pads in the caliper by hand. Lower the caliper into the left-front caliper bracket. Bolt it into place using the socket set.
7. Move to the Taurus' right-front brake assembly and repeat steps 3 through 6. Reinstall the wheels and lug nuts by hand.
8. Lower the front end off the jack stands. Tighten the front lug nuts to 85 foot-pounds with your torque wrench. Move the wheel chocks before driving the Taurus. Read More »»
Why Do Brake Lines Break?
A car's brake lines are needed to carry brake fluid to the brake pads at the car's wheels. Brake lines can break when they become weakened due to corrosion or rust, or from impact, such as in a car crash.
Brake Lines
When you press down on your car's brake pedal, you force brake fluid through the brake lines to a braking unit on each wheel. The fluid causes brake pads to press against the brake rotor, causing it to slow. The front and back wheels have rubber brake lines, because flexibility is required; otherwise, they are made from steel.
Causes of Damage to Rubber Brake Lines
Rubber brake lines deteriorate naturally over time, due to moisture and heat. They can also be corroded by the salt that is spread on icy roads in the winter . If the roads where you live are covered in salt in the winter, it is a good idea to wash your car's underbody regularly, to rinse off the salt and prevent damage to your brake lines.
Causes of Damage to Steel Brake Lines
The steel brake lines in a vehicle will eventually rust and break. Road salt can accelerate this process. As well, the force of impact from a car crash can cause steel brake lines to bend or collapse, which weakens them and renders them susceptible to breakage. If a steel brake line breaks, it is best to replace the complete line rather than trying to patch it. Read More »»
Brake Lines
When you press down on your car's brake pedal, you force brake fluid through the brake lines to a braking unit on each wheel. The fluid causes brake pads to press against the brake rotor, causing it to slow. The front and back wheels have rubber brake lines, because flexibility is required; otherwise, they are made from steel.
Causes of Damage to Rubber Brake Lines
Rubber brake lines deteriorate naturally over time, due to moisture and heat. They can also be corroded by the salt that is spread on icy roads in the winter . If the roads where you live are covered in salt in the winter, it is a good idea to wash your car's underbody regularly, to rinse off the salt and prevent damage to your brake lines.
Causes of Damage to Steel Brake Lines
The steel brake lines in a vehicle will eventually rust and break. Road salt can accelerate this process. As well, the force of impact from a car crash can cause steel brake lines to bend or collapse, which weakens them and renders them susceptible to breakage. If a steel brake line breaks, it is best to replace the complete line rather than trying to patch it. Read More »»
Audi Rear Brake Pads Installation
Brake pads are essential to the safety of your Audi. However, as they wear out, performance will gradually reduce and it will take longer to stop the vehicle. A new set of brake pads will rejuvenate the performance of the braking system and will get rid of any squealing caused by worn-out pads.Installation Procedure:
1. Slightly loosen each lug nut on the Audi's rear wheels, turning them counterclockwise with the wheel nut wrench no more than one full turn each. Doing this will make the nuts easier to remove after the car is jacked up.
2. Park the car and turn off its ignition. Place wheel chocks under the front wheels to prevent the Audi from moving. Position a jack under the center of the rear axle. Lift the car until there is adequate clearance to place jack stands on either side of the jack. Lower the jack until the stands are supporting the Audi's full weight.
3. Unscrew and remove the rear lug nuts. Take the wheel off. Remove the brake caliper by disconnecting the bolts located on the inner-most side. There will be two pads inside the caliper, which press on either side of the rotor while braking. Pry each pad out and set them aside.
4. Open and secure the car's hood. Remove the cap from the brake fluid reservoir. This will allow excess pressure to be released as you depress the caliper piston.
5. Using a "C" clamp on the caliper, carefully compress the piston until it is fully retracted inside the caliper.
6. Insert the replacement brake pads. Make sure the metal tabs are pressed completely inside the hole in the caliper. Reinstall the caliper and tighten the bolts that were previously removed. Follow the same procedure in the previous steps to change the brake pads on the other side of the car.
7. Place the cap back on the brake fluid reservoir. Put the wheels back on and tighten each lug nut. Remove the stands and lower the rear of the Audi. Tighten the lug nuts on the wheels. Read More »»
1. Slightly loosen each lug nut on the Audi's rear wheels, turning them counterclockwise with the wheel nut wrench no more than one full turn each. Doing this will make the nuts easier to remove after the car is jacked up.
2. Park the car and turn off its ignition. Place wheel chocks under the front wheels to prevent the Audi from moving. Position a jack under the center of the rear axle. Lift the car until there is adequate clearance to place jack stands on either side of the jack. Lower the jack until the stands are supporting the Audi's full weight.
3. Unscrew and remove the rear lug nuts. Take the wheel off. Remove the brake caliper by disconnecting the bolts located on the inner-most side. There will be two pads inside the caliper, which press on either side of the rotor while braking. Pry each pad out and set them aside.
4. Open and secure the car's hood. Remove the cap from the brake fluid reservoir. This will allow excess pressure to be released as you depress the caliper piston.
5. Using a "C" clamp on the caliper, carefully compress the piston until it is fully retracted inside the caliper.
6. Insert the replacement brake pads. Make sure the metal tabs are pressed completely inside the hole in the caliper. Reinstall the caliper and tighten the bolts that were previously removed. Follow the same procedure in the previous steps to change the brake pads on the other side of the car.
7. Place the cap back on the brake fluid reservoir. Put the wheels back on and tighten each lug nut. Remove the stands and lower the rear of the Audi. Tighten the lug nuts on the wheels. Read More »»
Change the Front Disc Pads on a 2005 Mitsubishi Galant
The front disc brake pads on the 2005 Mitsubishi Gallant rest inside the brake caliper. As you press on the brake pedal, a piston inside the brake caliper presses on the back of a brake pad inside the caliper. As a result, the pads create pressure on the brake rotor and stop the vehicle. The pads wear out much faster than the brake rotor and when they do wear out, you will hear a chirping sound every time you step on the brake. This means it is time to change the brake pads.Procedure:
1. Open the engine hood and remove the front cap from the master cylinder. The master cylinder is next to the firewall on the driver's side of the engine bay.
2. Loosen but do not remove the lug nuts on the driver's side wheel using the tire iron supplied with the Gallant.
3. Place a jack under the frame, directly behind the driver's side tire, and raise the vehicle high enough to place a jack stand under the frame beside the jack. Lower the Gallant onto the jack stand.
4. Remove the lug nuts using the tire iron and pull the wheel off the wheel studs. Place the wheel to the side.
5. Remove the two bolts that secure the brake caliper to the axle housing and then pull the caliper off the rotor. The brake pads will likely fall out of the caliper. Place the backside brake pad back into the caliper and discard the front side brake pad. You will use the backside brake pad to help push the piston back into the caliper.
6. Place a pair of vice grips over the backside brake pad and the backside of the caliper and squeeze the piston back into the caliper. Discard the old backside brake pad.
7. Place the new brake pads into the caliper. The brake pads rest inside grooved cutouts inside the caliper; they do not bolt into place.
8. Hold the pads in place as you slide the caliper back over the brake rotor.
9. Secure the caliper to the axle housing using the two bolts, socket and ratchet.
10. Place the tire back onto the Gallant an secure it to the wheel by threading the lug nuts onto the wheel studs. Give each lug nut a quarter turn using the tire iron.
11. Raise the Gallant with the jack until you can remove the jack stand. Lower the Gallant to the ground and tighten each lug nut using the tire iron.
12. Complete steps 2 through 11 for the passenger side brake.
13. Place the front cap back onto the master cylinder and close the engine hood. Read More »»
1. Open the engine hood and remove the front cap from the master cylinder. The master cylinder is next to the firewall on the driver's side of the engine bay.
2. Loosen but do not remove the lug nuts on the driver's side wheel using the tire iron supplied with the Gallant.
3. Place a jack under the frame, directly behind the driver's side tire, and raise the vehicle high enough to place a jack stand under the frame beside the jack. Lower the Gallant onto the jack stand.
4. Remove the lug nuts using the tire iron and pull the wheel off the wheel studs. Place the wheel to the side.
5. Remove the two bolts that secure the brake caliper to the axle housing and then pull the caliper off the rotor. The brake pads will likely fall out of the caliper. Place the backside brake pad back into the caliper and discard the front side brake pad. You will use the backside brake pad to help push the piston back into the caliper.
6. Place a pair of vice grips over the backside brake pad and the backside of the caliper and squeeze the piston back into the caliper. Discard the old backside brake pad.
7. Place the new brake pads into the caliper. The brake pads rest inside grooved cutouts inside the caliper; they do not bolt into place.
8. Hold the pads in place as you slide the caliper back over the brake rotor.
9. Secure the caliper to the axle housing using the two bolts, socket and ratchet.
10. Place the tire back onto the Gallant an secure it to the wheel by threading the lug nuts onto the wheel studs. Give each lug nut a quarter turn using the tire iron.
11. Raise the Gallant with the jack until you can remove the jack stand. Lower the Gallant to the ground and tighten each lug nut using the tire iron.
12. Complete steps 2 through 11 for the passenger side brake.
13. Place the front cap back onto the master cylinder and close the engine hood. Read More »»
Subscribe to:
Posts (Atom)