Monday, November 15, 2010

Floating Brake Rotors Vs. Solid Brake Rotors

Floating brake rotors are made from two pieces of metal instead of one solid piece. Floating brake rotors feature an outer ring that is contacted by the brake pads and an inner ring that attaches to the wheel.
Warping
Brake rotors can be subjected to extreme temperatures. Though the brake rotor is made from materials meant to withstand this temperature, rotors can and do warp. Floating rotors reduce the chances of warping as the outer ring can heat up and expand without impacting the inner ring which stays much cooler as it is not in contact with the brake pads.
Rotor Life
The constant expansion and contraction of the brake rotor will cause the rotor material to weaken and eventually fail. Floating rotors are less impacted by this heat as the outer ring is allowed to expand independent of the inner ring, giving the floating rotors a longer service life than solid rotors.
Cost
Solid brake rotors are much less expensive than floating rotors as they are much simpler to manufacture. Though more expensive to purchase than solid rotors, the longer life of floating rotors may offset their cost over the life of the bike.
Read More »»

How to Replace 2003 Buick Century Disk Brakes

You must check the brake pads and rotors on the Buick Century regularly to ensure they are in good working order. The brake pads wear much faster than the rotors. If you allow them to wear beyond the recommended minimum thickness, they will cause damage to the rotors, which could mean a much more expensive repair. You can complete this project in your driveway and it will take you about 30 minutes to do each wheel
Installation Procedure:
1. Park the car on a level surface and turn of its ignition. Open and secure the engine compartment of the Buick Century and drain about one-half of the brake fluid from the master cylinder, using the turkey baster. Place the fluid in the drain pan for later recycling.
2. Place the wheel chocks behind the rear wheels. Raise the Buick with the automobile jack. Place a jack stand under the car and raise it to the frame. Remove the lug nuts from the wheel using the lug wrench and pull the wheel off the car.
3. Remove the brake caliper using a socket and ratchet to loosen the bolts. Remove the front brake pad. Place the caliper and the back brake pad between the jaws of the C-clamp and spin it until it closes. This will push the caliper piston back in the housing. Loosen the C-clamp and pull the brake pad off the caliper.
4. Install the new brake pads in the caliper. Place the caliper back on the wheel assembly. Tighten the bolts with the socket and ratchet. Place the wheel on the car and tighten the lug nuts with the lug wrench.
5. Repeat the process on the other wheel. Remove the jack stand from under the Buick. Lower the car to the ground with the car jack.
6. Add brake fluid to the master cylinder, as needed. Pump the brakes several times until the brake pads settle against the brake rotors
Read More »»

How to Tell If Brake Rotors Need to Be Replaced

If you consider the brake system of your car the first line of defense against accidents, the brake rotors control the action of the brakes. When you step on the brake pedal inside the car, the brake rotors squeeze the brake pads, which in turn makes the wheels stop safely. Knowing when to replace the brake rotors is important to the health of your brake system and the safety of your car.
Procedure to replace Brake Rotors:
1. Listen to the sound coming from your car when using the brakes during a drive. If you hear any scraping or grinding noises when you engage the brakes, inspect the rotors immediately.
2. Turn the steering wheel all the way to the right or left and park the car. Moving the wheel to the extreme will expose the brake rotor.
3. Locate the rotor behind the wheel. The rotor is shaped like a disc and runs in between the brake pads.
4. Read the writing on the rotor to find the recommended thickness from the manufacturer. The numerical measurement is the minimum thickness at which the rotor can be operated.
5. Measure the thickness of the rotor with a measuring tape. If it is lower than the number written on the rotor, it needs replacing.
Read More »»

Replace Shims and Clips on New Rear Brake Pads

Disc brakes work by two brake pads being pressed against a spinning rotor attached to the axle. As the pads press onto the rotor, friction is created, thereby slowing down the rotor and wearing on the pads. This wear forces the brake pads to be replaced regularly over the life of the vehicle. The pads must press evenly on both sides of the rotor to work correctly. Small, stainless shims can be placed in the brake pad tracks to help the pads move evenly, and clips are attached to the brake pads to indicate when they are worn out.

Only 5 steps you need to do:
1. Hold a brake pad in your hand and press the fitting of the clip onto the end of the brake pad's backing. The brake pad clip is J-shaped; the top of the J should be pointed toward the pad portion of the brake pad.
2. Insert the clips for the other brake pads.
3. Use steel wool to clean off any corrosion and dirt in the brake pad tracks of the brake assembly.
4. Press the shims into each of the brake pad tracks so that the shim fits the shape of the brake assembly.
5. Insert the brake pads into the brake pad tracks, on top of the brake shims.
Read More »»

Remove a Volvo 240's Turn Signal Lights

How to Remove a Volvo 240's Turn Signal Lights? State laws require you have working turn signals in your car to let other drivers know your intention. You may want to remove the turn signal lights from your Volvo 240 because of car accident damage, for instance, or you may desire to have old turn light assemblies replaced with new ones. Removing the turn signal lights from your Volvo 240 yourself does not take much time, plus you can save money in labor costs

Below is the instruction procedure:
1. Loosen the Phillips screws of the turn signal lights in your Volvo 240 with a Phillips screwdriver.
2. Remove the bulb lens.
3. Press the bulbs in, and then turn them slightly counterclockwise to remove them from the turn signal assembly. Put the bulbs in a safe location.
4. Unscrew the retainers to the turn signal light assembly. The retainers hold the turn signal in place.
5. Pull out the old turn signal light assembly Read More »»

Replace the Front Brakes on a 1997 Mazda Protege

The front brakes on the Mazda Protégé are easy to replace. You can expect it to take you about 30 minutes to replace the brake on each wheel. When you are replacing the brake pads, it is a good time to inspect the brake rotors for surface damage. Any grooves or other damage on the rotors will need your attention. You can complete this project in your driveway, saving you from paying the labor costs at a repair shop.

Procedure:
1. Place the Mazda on a level surface and turn off the key. Open the engine compartment and drain half of the brake fluid from the brake master cylinder using the turkey baster. Place the fluid in the drain pan for proper recycling later. The master cylinder is at the back of the engine compartment on the driver's side.
2. Place the wheel chocks behind the rear wheels of the Protégé. Raise the car up with the jack. Place a jack stand under the Mazda and raise it to the frame of the car. Remove the lug nuts from the wheel with the lug wrench. Pull the wheel off the car.
3. Loosen the bolts on the brake caliper with a socket and ratchet and pull it from the mounting bracket. Place the caliper and the back brake pad into the jaws of the C-clamp and turn the handle until the jaws of the C-clamp push the caliper piston back into the caliper housing. Remove the brake pads from the caliper.
4. Place a new set of brake pads into the caliper. Put the caliper on the mounting bracket and tighten the bolts with the socket and ratchet. Put the wheel on the car and tighten the lug nuts with the lug wrench. Remove the jack stand from under the Mazda. Lower the car to the ground. Repeat the process on the other wheel.
5. Add fresh brake fluid to the master cylinder as needed when both wheels are complete. Pump the brakes several times until the pedal feels firm. This will seat the brake pads against the brake rotor. Check the brake fluid to see if you need to add more to the master cylinder. Never add fluid above the "Max" line. Read More »»

Replace the Rear Disc Brakes on a 1991 Nissan 240SX

How to Replace the Rear Disc Brakes on a 1991 Nissan 240SX? The 1991 Nissan 240SX is equipped with front and rear disc brakes. Disc brakes use two pads pressing on a flat rotor, often called the disc, to create friction. The friction stops the car, but it also causes the pads to wear, and, eventually, you will need to replace them. How long the pads last depends on how you drive the car. When the pads get thin, a piece of metal will contact the rotor when you depress the brake pedal, and you will hear a high-pitch squeal.

1. Loosen the lug nuts on both rear wheels. Ensure the parking brake is released.
2. Raise the vehicle, using the automotive jack, and support both sides with a jack stand. Remove the lug nuts, and take off both wheels.
3. Place a drip pan under the brake assembly, and saturate all brake components with brake cleaner. This will remove the harmful brake dust that accumulates on the brake assembly. Allow the parts to dry.
4. Use a wrench or socket to remove the parking brake cable stay fixing bolt. The bolt is on the bottom, back side of the brake cylinder body.
5. Use a wrench or socket to remove the lower cylinder body pin bolt. This bolt is directly below the cable stay fixing bolt you removed in Step 4.
6. Rotate the cylinder housing up and off the rotor.
7. Remove the pad retainers that hold the inner and outer pads in the housing, and remove both pads and shims. The retainers are flat, metal clips on each end of the pads.
8. Use a pair of needle-nose pliers to turn the piston clockwise, screwing it back into the housing. This is to provide room for the new pads, since they will be thicker than the old ones.
9. Apply a coat of high-temperature grease to the rear of both pads. Place the new shims on the back of the pads, and apply a coat of grease to the shims. The new pads should come with a small tube of this grease.
10. Insert the pads back into the housing, and secure them in place with the pad retainers.
11. Rotate the housing back down onto the rotor.
12. Replace the lower pin bolt, and tighten it to between 16 and 23 ft-lbs. of torque, using a torque wrench.
13. Reattach the parking brake cable stay, and tighten the fixing bolt to between 20 and 27 ft-lbs. of torque.
14. Ensure there is no grease or oil on the brake rotor. If there is, clean the rotor with brake cleaner. Repeat the procedure to replace the pads on the opposite side of the car.
15. Replace both wheels and lug nuts. Lower the car, and tighten the lug nuts Read More »»